If you stop the installation now, some software will not be installed.
Are you sure you want to stop?
There is no more software to install.
The installation process has been stopped. Some software has not been installed.
What do you want to do?
• Try to install this software item again
• Stop the entire installation process
• Skip installing this software item only
All installations that could be completed are finished. Some installations could not be completed.
Click Stop to halt the installation process.
An error has stopped the installation process. Some software has not been installed.
What do you want to do?
• Try to install this software item again
• Stop the entire installation process
• Skip installing this software item only
If you stop the installation process now, some software installers will not be launched.
Are you sure you want to stop?
There are no more software installers to launch.
The installation process has been stopped. Some installers have not been launched.
What do you want to do?
• Try launching this software installer again
• Stop the entire installation process
• Skip launching this software installer only
The installations or removals that could be completed are finished. However, some could not be completed.
Click Stop to check the status of the installations or removals.
An error has stopped the installation process. Some installers have not been launched.
What do you want to do?
• Try launching this software installer again
• Stop the entire installation process
• Skip launching this software installer only
The disk “^0” could not be checked.
Problems were found with “^0” that cannot be fixed by this program. See your installation manual for instructions.
Problems were found with “^0” that cannot be fixed by this program. See your installation manual for instructions.
The disk “^0” is being used by another application. Please quit all other applications and try again.
Problems were found on the disk “^0”, but the disk cannot be fixed now. Try starting the installation again.
Problems were found on the disk “^0”, but they have been fixed.
Problems were found on the disk “^0”, but they cannot be fixed because file sharing is turned on. Turn off file sharing (in the Sharing Setup of File Sharing control panel) and try again.
Problems were found on the disk “^0”, but they cannot be fixed because the disk is locked. Unlock the disk and try again.
Problems were found on the disk “^0”, but they cannot be fixed because the disk is the startup disk. Start up your computer with the CD or startup floppy disk that came with this upgrade kit, then try again.
Problems were found on the disk “^0”, but they cannot be fixed because one or more files are open. Please quit all open applications and try again.
The selected destination disk is invalid or has unexpectedly disappeared.
Click OK to select another destination disk.
Your computer must have System 7.1.2 or later in order to update the Apple hard disk drivers. Click Cancel and start up your computer using the disk that came with your upgrade kit, then run this program again.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk is not an Apple hard disk. Contact the manufacturer of your computer or hard disk to see if you need to update the driver.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk has been formatted with a non-Apple disk utility. Contact the manufacturer of the disk utility to see if you need to update the driver.
The Apple hard disk driver on the disk “^0” was not updated. Errors were encountered. See the troubleshooting section of your installation manual for more information.
The hard disk driver on the disk “^0” cannot be updated with this program because the disk is write protected.
The installation plug-in could not be loaded.
The installation process has been stopped. Stopping now may prevent your computer from starting up.
Click Continue to proceed with the installation.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) returned an internal error.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) could not be found.
Preflight code resource (Type: '^0', ID: ^1, RefCon: ^2) could not be loaded.
The helper application “^0” unexpectedly quit. The installation process has been stopped.
This product cannot be installed while running on this system software. Please restart your computer with system software of the same language as the product you are installing, then try the installation again.
The disk “^0” could not be remounted after disk verification was complete. If this is disk requires a password, turn off password protection then try the installation again.
